good news! From today onwards, the Lion Dance and Shenchuan will implement the nationwide guarantees! ! Hehe. No matter how far away you are, as long as there is a local agent, you can get the local Lianbaola~~
The shopkeeper promises: All electric tools sold in this mall are all-copper motors and genuine products! So dear ones can rest assured to buy! They are all purchased directly by manufacturers, so there are a lot of discounts in terms of prices! The motor is guaranteed for three months, and is based on the standards of professionals, so you can use it with confidence!
The manufacturer of the heat insulation cover is not equipped, please pay attention to it! Minor changes will not be notified separately, the actual product shall prevail!
Instructions
Install or remove the grinding head
note:Before installing or removing the grinding head, be sure to turn off the tool power switch and unplug the power plugPlease use only the wrench that comes with the tool.
When installing the grinding head, first insert the grinding head as far as possible into the tapered chuck, insert the large-opening wrench into the flat square of the output shaft and fix it, then insert the small-opening wrench into the elastic chuck, and press the wrench clockwise. Tighten the elastic chuck in the direction. Be sure to tighten the elastic chuck. When disassembling the grinding head, repeat the above installation steps in reverse order.
Switch operation
note:Before inserting the power plug of the tool into the power socket, be sure to check whether the switch board is operating normally
And whether it can return when released“O”Location.
To start the tool, just switch the switch to “ON”Then, the tool stops immediately.
Grinding and sanding operations
caveat:1, Do not use force when operating tools. The weight of the tool can apply enough pressure, over-applying
Force can cause damage to the grinding head, which is dangerous.
2, If the tool falls during the grinding operation, the grinding head must be replaced.
3, Do not knock the workpiece with the grinding head, this will cause the damage of the grinding head and cause danger.
4, The bounce and obstruction of the grinding head should be avoided to prevent the grinding head from losing control and rebounding, which may cause loss of control.
Personal injury accident. Especially when working on corners or sharp edges.
note:After the operation is completed, be sure to close the tool and wait for the grinding head to completely stop rotating.
lay down. For smaller workpieces, be sure to clamp the workpiece with a vise or similar fixing tool.
Please be sure to hold the tool firmly with both hands, and then do not restart the tool.
on.
maintenance
note:Be sure to turn off the tool power switch and unplug the power plug before checking or maintaining the tool.
Tools and exhaust and suction holes must be kept clean. The suction hole of the tool exhaust should be cleaned regularly or at any time when it is blocked.
Clean up.
How to buy electric grinders At present, there are many brands of electric grinders on the market. There are a large number of manufacturers at home and abroad that produce this kind of practical tools. The price varies greatly from more than one hundred yuan to thousands of yuan. The quality is also uneven, which brings a certain degree of difficulty in selection. According to my personal experience, pay attention to the following points when choosing this type of tool to choose a satisfactory electric grinder:
（1）, Pay attention to whether it is a regular manufacturer''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s brand. The products of regular manufacturers have complete “three certificates”, and have passed “3C” certification, complete accessories, perfect after-sales service, and trustworthy.
（2）, The high-quality electric grinder adopts high-quality motors and engineering plastics, and adopts a double insulation structure, which is safe and *, and has a built-in interference suppressor to prevent interference with TV, broadcasting and radio equipment. The appearance design is reasonable, and the hand feels better. More delicate, this is the product of some small workshops that cut corners and can''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''t match the beauty. Small places like switches, governors, and power cords can more intuitively reflect the quality requirements and craftsmanship of the manufacturer. It is undoubtedly for you to choose products with the highest quality. Safety and durability are added a guarantee.
（3）Another more intuitive identification method is to put two or more electric grinders together and identify them by sound after power on, because most of the current electric grinders are adjustable speed types in the range of 0rpm to 30000rpm, and are of high quality. The power is strong, the acceleration is fast and powerful, while the poor quality power and acceleration are weak, and the power is obviously insufficient, not up to the standard, and even with abnormal noise. Such a product is difficult to guarantee the quality, and it is not easy to use.
The real charm of the mold electric grinder is that it can be used with various abrasives for cutting, dressing, modeling, grinding and polishing of metal and non-metal materials. Its main abrasives include:
（1）Cutting category: resin high-speed cutting sand sheet, cutting sand sheet with cloth net, emery cutting sheet
（2）Grinding categories: various special-shaped ceramic grinding heads, sand rings, sand drums, and shank page wheels
（3）Polishing category: wool felt wheel, felt piece, small cloth wheel, steel wire brush, copper wire brush（Polishing paste for various purposes）